• Fits 302/351W Ford Racing Blocks
• Common outer diameter service replacement cam bearings for use in the following Ford Racing cast iron blocks:
  
• M-6010-R302
• M-6010-S302
• M-6010-R351
• M-6010-R352
• M-6010-S351
• M-6010-V351
• M-6010-W351
• M-6010-R451
• M-6010-R452
• M-6010-R453
• M-6010-B302BB
• M-6010-BOSS302
• M-6010-BOSS35192
• M-6010-BOSS35195
• M-6010-BOSS351BB.
• Use with standard/conventional/off-the-shelf camshaft designs where the 1-4 bearings are common but the 5the bearing is a different size.  If your camshaft is a custom ground camshaft with 1-5 common bearings, then you need to use M-6261-R351 cam bearing kit.
  

• Fits 289-302 engines with production heads and "X" or "Z" heads
• 8740 steel alloy
• Includes 12-point nuts and hardened washers
• 7/16 inch size
• Sold In engine sets

• 1/2" cylinder head bolts required for installation of the Ford Racing M-6049-X306/X307/Z304DA heads onto the M-6010-BOSS302, M-6010-B302BB, M-6010-BOSS35195, M-6010-BOSS35192, M-6010-BOSS351BB blocks.
  
• Includes hardened washers
  
• Sold in engine sets
  

• Use when installing stock 351W, Ford Racing cast iron (M-6049-L302/L303) or Ford Racing aluminum head (M-6049-Y302/Y303/X302/X303/X304/X305/X306/X307) on 289/302 blocks
  
  
• Kit features 20 ARP cylinder head bolts with 7/16" diameter thread
  
  
• Includes 20 special stepped washers
  
  
• Sold in engine sets
  
  

• Use when installing M-6049-Z304/Z304A/Z304D/Z304DA heads on a 351W block (except Boss 351 block)  
• 1/2" diameter studs with 12-point nuts and hardened washers  
• Sold in engine sets  

• Engine mounts used when installing M-6010-BOSS302 or M-6010-BOSS35195 block in S197 Mustang Cobra Jet.
  
• Includes left and right engine mounts
  
• Steel construction

Designed to install the M-6010-BOSS50 block in a 2005-2010 Mustang

• Aluminum engine mounting brackets
• Adapter plates
• Hardware

• 1/2" cylinder head studs required for installation of the Ford Racing M-6049-X306/X307/Z304DA heads onto the M-6010-BOSS302, M-6010-B302BB, M-6010-BOSS35195, M-6010-BOSS35192, M-6010-BOSS351BB blocks.
• Includes 12-point nuts and hardened washers
• Sold in engine sets

• Stud Kit fits Mirror Head M-6049-JC50 only  
• Complete fastener kit includes studs, washers and twelve point nuts  
• Produced by ARP of premium material    
• Sold in engine sets

• Stud Kit fits Sequential Head M-6049-JC51 only
  
• Complete fastener kit includes studs, washers and twelve point nuts
• Produced by ARP of premium material
• Sold in engine sets

Only the bold need apply, this 10-rib supercharger drive kit is for those seeking maximum performance out of their supercharged 5.0L Mustang. Developed for the 2013 Cobra Jet the 10-rib accessory drive system is for high rpm or high boost 5.0L supercharged engines.

• Includes all fasteners, adapter plates, alt. pulley, water pump pulley, five idler pulleys, and exclusive Aramid cord belt for maximum durability
• All aluminum bracketry, pulleys, and adapters are anodized for a durable surface finish and corrosion resistance
• All fasteners are high grade stainless steel
• Recommended for use with ATI 10% overdrive SFI crankshaft damper (P/N SK109JZ) and Thump Racing billet tensioner PM-1005-GT500 (factory 5.4L tensioner 7R3Z-6B209-AA can be used but not recommended)
• Works with all Ford Racing/Whipple 5.0L supercharger kits (Whipple 10-rib supercharger up-fit required on 2.3L, 10-rib pulley required for 2.9L/4.0L, contact Whipple Superchargers for details) 
• Retains all factory accessories.